Cheap Clay Ceramic Water Permeable Bricks Tiles For Pavers
- Category: Bricks >>>
- Supplier: Yixing,Longguan,Ceramics,Co.,Ltd.
Share on:
Product Overview
Description
Product Description
There are two types of ceramic permeable bricks. One is a high-quality permeable building
material formed by using ceramic raw materials through sieving and selecting materials, organizing a reasonable particle gradation, adding a binder, and forming, drying, and sintering at a high temperature. The other is a high-quality water-permeable building material that uses ceramic raw materials through sieving, reasonable organization of particle gradation, and addition of binders, followed by molding, drying, and pressing. Features are as follows:
1. High strength.
The product is fired at a high temperature of 1115°C. The combination of the product is formed by melting the physical components between the particles and then cooling, and the strength is very high. Usually greater than 45 MPa.
4. Good anti-skid performance.
The surface particles are relatively coarse, the rainwater penetrates quickly, there is no accumulation of water and no ice layer after the rain and snow, and the anti-skid effect is the best.
6. It can improve the urban microclimate and block the formation of urban floods.
The porosity of the ceramic permeable brick is 20-30%, and it has good water storage capacity. In summer, after the rain, water is absorbed and penetrated into the ground to nourish the ground gas, conserve water, and provide water to trees and flowers; when
the sun is strong , Water evaporation can lower the surface temperature and improve the microclimate. If a large area of paving is formed, rainwater can be effectively blocked and the probability of urban flood formation can be reduced.
material formed by using ceramic raw materials through sieving and selecting materials, organizing a reasonable particle gradation, adding a binder, and forming, drying, and sintering at a high temperature. The other is a high-quality water-permeable building material that uses ceramic raw materials through sieving, reasonable organization of particle gradation, and addition of binders, followed by molding, drying, and pressing. Features are as follows:
1. High strength.
The product is fired at a high temperature of 1115°C. The combination of the product is formed by melting the physical components between the particles and then cooling, and the strength is very high. Usually greater than 45 MPa.
2. Good water permeability.
With a reasonable particle gradation, the precipitation of small to moderate rain can be quickly passed through.
With a reasonable particle gradation, the precipitation of small to moderate rain can be quickly passed through.
3. Good freeze-thaw resistance.
Due to the large pores between the particles, the combination is sintering and has good resistance to freezing and thawing in the north. It is a good solution to the problem that the permeable cement brick is not permeable if it is resistant to freezing and thawing, and that it is impermeable if it is resistant to freezing and thawing.
Due to the large pores between the particles, the combination is sintering and has good resistance to freezing and thawing in the north. It is a good solution to the problem that the permeable cement brick is not permeable if it is resistant to freezing and thawing, and that it is impermeable if it is resistant to freezing and thawing.
4. Good anti-skid performance.
The surface particles are relatively coarse, the rainwater penetrates quickly, there is no accumulation of water and no ice layer after the rain and snow, and the anti-skid effect is the best.
5. Good ecological and environmental protection performance.
It can be produced from industrial wastes such as ceramic waste, sewage sludge particles, waste refractory materials, etc., and can be reused. After being broken, it can be fired into bricks again.
It can be produced from industrial wastes such as ceramic waste, sewage sludge particles, waste refractory materials, etc., and can be reused. After being broken, it can be fired into bricks again.
6. It can improve the urban microclimate and block the formation of urban floods.
The porosity of the ceramic permeable brick is 20-30%, and it has good water storage capacity. In summer, after the rain, water is absorbed and penetrated into the ground to nourish the ground gas, conserve water, and provide water to trees and flowers; when
the sun is strong , Water evaporation can lower the surface temperature and improve the microclimate. If a large area of paving is formed, rainwater can be effectively blocked and the probability of urban flood formation can be reduced.
Product Specification
Place of Origin | China |
Material | clay |
Color | Yellow,Red,Grey,White or custom |
Shape | rectangle |
Characteristic | Resistant to pressure, cold and corrosion |
MOQ | 1000 |
Regular Size | 100*100*55mm,200*100*55cm,200*200*55mm,200*400*55mm,400*400*55mm,300*150*55mm,300*300*55mm,300*600*55mm,Can be customized |
Product weight | 1.97kg |
Delivery date | 15 |
Product Case
Company Profile
Product Line
Packing & Delivery
Certifications
FAQ
1.Are you a manufacturer or a trading company?
Yes, we are manufacturer. But we also have trading business in other areas. We can help find suppliers.
2.What is your delivery day?
It depends on the colors you ordered, if the colors you like are available, we can delivery the goods in 15 days after receiving advance payment. If stock not available, we can arrange production immediately.
3. If you can do OEM for me?
Yes, we can make the roof tile's design as you require and do the packing as you like.
4.What kind of export do you accept?
FOB, EXWORK, CIF, C&F
5. What is your MOQ ?
If our regular size, our MOQ is 500 Square Meters.If you need to customize ,our MOQ is 1000 Square Meters.
Yes, we are manufacturer. But we also have trading business in other areas. We can help find suppliers.
2.What is your delivery day?
It depends on the colors you ordered, if the colors you like are available, we can delivery the goods in 15 days after receiving advance payment. If stock not available, we can arrange production immediately.
3. If you can do OEM for me?
Yes, we can make the roof tile's design as you require and do the packing as you like.
4.What kind of export do you accept?
FOB, EXWORK, CIF, C&F
5. What is your MOQ ?
If our regular size, our MOQ is 500 Square Meters.If you need to customize ,our MOQ is 1000 Square Meters.
