Their own power consumption is less than 20mA (it is 7mA when the programmer is not programming, LED power indicator use largest electricity, 5mA each one) and Programming
power loss rate is less than 20% so that the programmer can supply the high VCC VPP programming electric current. Programmable chip can be provided with enough programming power (the largest programming power output is 2 watts that is impossible for a chip to use 2 watts of programming power).
And you hardly feel the heat of the programmer after such long continuous work.
Easily portable performance
This is one of the smallest products in the world and the dimensions are 10CM*6CM*2.5CM (it is as small as a driving license). In addition, you don't need to carry with an external power supply because of its ultra-low power that makes it more portable.
Programmable programming power supply
VPP and VCC programming voltages are independently program-controlled: programmable VCC is from 1.8V to 6.5V; VPP is from 1.8V to 18V. The fluctuation of power supply is minor because of the multi-stage LC filter.
Best overvoltage, overcurrent protection
VCC, VPP power supply of the Programmer is furnished with the independent Grade 3 overcurrent protection and the protection of automatically cutting off power supply.
Each pin of 40-pin programming socket has VPP overvoltage protection.
It can effectively
prevent from putting a chip in the wrong place or short circuit due to other reason. In this programming case, it can also stop VPP high voltage from coming back to the internal of the programmer and damaging the device.
Really make sure that the programmer will not be damaged when there is any worst-case short circuit. At the same time, the programmed chip can be efficiently
This programmer will cut off the programming power supply VPP and VCC within 100us and send the message to the application program when there is short circuit. The programmer and PC won't be reset when there is short circuit because of the multilevel overcurrent protection.
40PIN universal pin
It is the most versatile pin among 40PIN quasi-universal pins. You don't need to move or turn around the chip when programming,just congruously put the chip forward and the handle direction of the programmer is the PIN1 place.
Its design accords with the common operating habit of user.
This programmer is equipped with upgrading Function of the built-in hardware firmware program that can make sure your programmer's firmware flash and application software can be timely updated.
You can complete the upgrade by downloading the upgrading program through the manufacturer's website.
Second development function of chip serial number
This programmer has a variety of automatic numbering functions that are used commonly. You can get any serial number through DLL
Dynamic Link Libraries by using the custom algorithm. In mass production, the function enables each chip to produce only one identifying information that can be encrypted by the custom algorithm.
So you can effectively protect your rights as a customer.
Unique universal serial programming interface ICSP
This TL866ll Plus programmer can program through the 40-PIN universal socket and is provided with an ICSP serial programming port.
For some in-circuit serial programmable chips, you can program MCU by choosing ICSP port. You can get the clear instruction diagram in the programming software for the ICSP port wiring method. That is to say, you can directly program and update the chip soldered on the board.
Note: Now ICSP can in-circuit serial program ATMEL89S51, ATMEL89S52, AT45DBxxx, a whole series of AVR ATMEGAxxx, MICROCHIP PIC10Fxxx 12Fxxx 16Fxxx 18Fxxx, as well as a full serial of SYNCMOS SM59Dxx SM59Rxx.
The variety of microcontroller that can be supported in-circuit programming will be continually increased in the future. Six ICSP wires of this programmer, except a ground wire, other wires led full functional I2C, SPI and UART serial main wire, be suitable for all kinds of serial communication.
In addition, each wire can supply VCC, VPP or GND with high current.
54/74F/LS/HC CMOS4000 series IC functional tests
This is the first development programmer to test the common logic integrated circuit and this test can be located the errors of logic gate circuit, as well as test any possible input combinations of integrated circuit.
Programmer self-testing function
This programmer can test itself on each pin of VPP, VCC, GND and I/O information, at the same time it can run an inside short-circuit test on VPP, VCC current.
AVR microcontroller one-to-one soft encryption
AVR microcontroller has an RC Calibration (calibrate bytes). Only one of dozens of chips may have the same bytes value and it cannot be modified. Microcontroller software can read this value and determine whether the code is used by other chips.
Through custom encryption algorithm, it can stop those who decrypt chips with ulterior motives from directly using.
The encryption algorithm is so complex that it is not easy to decrypt. But, about "encryption", there is a problem for developers - each chip is different - it is impossible to manually calculate one by one and respectively compile source code if the algorithm is complex.
This programmer can automatically read into RC bytes before programming.
The developer can get the bytes value of the chip in the DLL dynamic function and then automatically calculate the encrypted data according to the request and put it in the memory,
efficiently completing mass production.
(A detailed encrypted instance of the ATMEGA8 in the installation package is available for reference)
Unified and convenient user interface
The user interface is well-designed and is in complete accord with the operating habit of the Windows series of software. Built-in binary editer is comparable to pure professional editing software. You can directly read, write and modify the files such as BIN format, HEX format, JED format and so on. In addition, it has the complete and practical project mode that makes the mass production more convenient and safer.
Product Includes the Following (for TL866II PLUS WITH 28 adapters)
1.Universal programmer: TL866II Plus 1 pcs
2.USB cable and ICSP cable: 1 pcs
3.TSOP32/40/48 with black socket: X1pcs
9.SOP44 with socket: X1pcs
10.SOP44 simple board: X1pcs
15.SOP8 208mil: X1PCS
16.SOP8 150mil: X1pcs
17.SOP28 300mil: X1pcs
18.SOP16 150mil: X1pcs
19.SOP16-DIP8 300mil: X1pcs
24.PLCC EXTRACTOR :X1pcs
25.SOIC8 clip: X1pcs
26.SOP16 300mil: X1pcs
31.SOP8 clip: X1pcs
The difference between the TL866CS and TL866A
1. ICSP interface (6-pin interface of the programmer right side) is limited to the TL866A model.
2. Partly Microchip's MCU with More than 40pins require the use of the TL866A for ICSP interface programming .Most of Microchip's PICs MCU support programming on ICSP and 40PIN seat.
3. About ATMEGAxxxx and SYNCMOS’s MCU SM89xxx SM59xxx
TL866A support serial programming on ICSP and parallel programming on seat.
TL886CS only support parallel programming on seat.
4. AT45DBxxxx can only be programmed using the ICSP interface (TL866A only).
5. To all other chips. TL866A and TL866CS no diffrent.
Both programmers work with genuine TL866 Adapters for devices up to 48 pins.