Профессиональный 2*800W 2*1000W 2*1300W 2*1600W 2U модуль Soundking усилитель мощности

Сохранить в закладки:


Цена:*
Стоимость в USD:Показать (текущая цена)

Количество:

  • В избранное

Описание и отзывы

Характеристики



Product Description


Professional 2*800W 2*1000W 2*1300W 2*1600W 2U Module Soundking Power Amplifier




1. Mains Power Switch
When press the switch, the soft start circuit run for avoiding surge strike. In about 3-4 seconds, there will be a clicking
denote that soft start finished. And more 1-2 seconds later, there will be another “clicking”, the amplifier is connected with
speaker and ready to work.
2. CH-1/CH-2 Input level control
Adjust it to get the volume desired. Use CH-1 control only while amplifier is set in Bridge or Parallel mode.
3. CH-1/CH-2 Protection indicating LED
This red LED will light up when the amplifier is running un-stable or went in to thermal protection after the power elements
temperature over 90℃.
4. Clip LED
Turns on just before the maximum, distortion free, output level of the amplifier. The clip Leds may turn on shortly from time to time but they may certainly not turn on for longer periods. In this case you have to turn the output level down!— 3 —
5. Signal LED
The green signal led indicates that a music signal is present at this channel input.
6. Parallel mode indicating LED
Indicate that the amplifier is working under parallel mode, the indicator is lighten, input signal only acts on CH-1.
7. Bridge mode indicating LED
Indicate the amplifier is working under BRIDGE mode, the indicator is lighten , and the input signal only acts on CH-1


1. CH-1/CH-2 input XLR
standard XLR jack, below is the connection method;
Pin1: signal ground, Pin2: signal+, Pin3: signal-
2. CH-1/CH-2 Signal Link Output
Standard XLR (male) socket for input signal link, its Pins parallel connected with the female XLR socket so you can feed the same signal to another amplifier. Pin1: signal ground, 
Pin2: signal+, Pin3: signal- 
3.INPUT SENSITIVITY SWITCH.
With this switch you can perfectly adapt the input sensitivity of the amplifier:26dB;1.4V;0.77V
4. CH-1/CH-2 35Hz HPF.
The low cut filter cuts all undesired frequencies below 35Hz.protecting woofers against excesslve swings.
5. Output Mode Set Switch.
Select the run mode as STEREO or BRIDGE or PARALLEL
6. Resettable fuse
When the amplifier malfunctions, the fuse will automatically disconnect the circuit loop; after the trouble is removed, the fuse will automatically reset, and resume working.
7. CH-1/CH-2 output SPEAKON
Standard Speakon socket. 1+ 2+ :, 1- 2-: -
8. Binding post outputs
These posts will accept bare wire cables that connect to your speakers.
9. Mains Power Supply Cord



Specification


                    GW800
                       GW1000
Power handling
800W*2(8Ω)/1200W*2(4Ω)/2400W (8Ω)
1000W*2(8Ω)/1500W*2(4Ω)/3000W (8Ω)
Output Connections
Speakon & Binding Post
Frequency Response
20Hz-20KHz ±0.5dB
XLR-f
Input Sensitivity
0.775V/1.4V/26dB
XLR-m
Input Impedance
20kΩ/Balanced,10kΩ/un-Balanced


20kΩ/Balanced,10kΩ/un-Balanced

S/N Ratio
≥100dB
< 1%
THD
≤0.03%


20Hz-25kHz, ±1dB

Crosstalk @ Rated
Output/8Ω/1kHz

>70 dB


AC: 220-230V 50Hz

Damping
Factor/8Ω/1kHz

>240
12.4
Slew Rate
15V/uS


482*326*88mm

Protection
Soft Start,Short Circuit,Limiter,DC Fault,AC Line Fuse,Thermal Cut
Cooling system
Two steps speed fan
Mains Power supply
AC:220~230V 50Hz
Weight
23.5KG
25.2KG
Dimensions (WxDxH)
482x464.5×88 mm


GW1300
GW1600
Power handling
1300W*2(8Ω)/2000W*2(4Ω)/4000W (8Ω)
1600W*2(8Ω)/2400W*2(4Ω)/4800W (8Ω)
Output Connections
Speakon & Binding Post
Frequency Response
20Hz-20KHz ±0.5dB
Input Sensitivity
0.775V/1.4V/26dB
Input Impedance
20kΩ/Balanced,10kΩ/un-Balanced
S/N Ratio
≥100dB
THD
≤0.05%
Crosstalk @ Rated
Output/8Ω/1kHz
>70 dB
Damping
Factor/8Ω/1kHz
>240
Slew Rate
15V/uS
Protection
Soft Start,Short Circuit,Limiter,DC Fault,AC Line Fuse,Thermal Cut
Cooling system
Two steps speed fan
Mains Power supply
AC:220~230V 50Hz
Weight
26.5KG
27.5KG
Dimensions (WxDxH)
482x464.5×88 mm
















Похожие товары

0.0175 s.