DC 5V 12V 24V LED Light Digital Time Delay 1 Way Relay Trigger CycleDC 5V 12V 24V LED Light Digital Time Delay 1 Way Relay (1600257376583)

Share on (1600257376583):


Price:$2.15 - $2.28

Quantity:


Product Overview

Description



Product Features:
* Wide voltage power supply (6 ~ 30V) supports micro USB 5.0V power supply, easy to use;
* The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
* There is a key stop function (STOP key), with reverse polarity protection, reverse polarity does not burn;
* Increase the sleep mode, it enables, without any operation within 5 minutes, turn off the monitor automatically; any key to
wake up;
* You can set a different OP, CL, LOP parameters, which are independent of each other, were saved;
* All setup parameters are saved automatically power down.


Product parameters:
* Operating voltage: 6--30V support micro USB 5.0V power supply
* The trigger source: high trigger (3.0V-24V) signal with no common ground system to improve anti-jamming capability of the
system (also self-shorting common ground)
* Output capability: You can control the DC or AC within 30v 5A within 220v5A
* Quiescent Current: 20mA Operating Current: 50mA
* Timing range: 0.1 seconds -999 minutes continuously adjustable;
* Availability: more than 10 million times;
* Working temperature: -40-85 Celsius ;
* size: 6.2 * 3.8 * 1.7cm
* with optocoupler isolation, enhanced anti-jamming capability, industrial grade circuit boards, set the parameters after power
failure memory forever.
* Special Note: The relay outputs are passive contact, uncharged output to control a line-off role.


Product Manual:

Operating mode:
* P1: After the trigger signal, the relay is turned OP time, and then disconnect; in the OP time, as follows
* P1.1: Invalid signal triggered again
* P1.2: Re-timing signal is triggered again
* P1.3: Reset signal is triggered again, the relay off, stop the clock;
* P-2: to the trigger signal, the relay after time off CL, OP relay conduction time, after the counting is finished, disconnect
relay;
* P3.1: After the trigger signal to the relay turned OP time, relay off CL time, then the operation cycle, to signal to the relay
off, stop the clock once again within the loop; cycles (LOP) can be set;
* P3.2: After power without triggering signal, the relay is turned OP time, relay off CL time, cycle the operation; cycles (LOP)
can be set;
* P-4: signal holding function if there is a trigger signal timing is cleared, the relay remains on; when the signal disappears,
after timing OP disconnect relay; timer period, then there is a signal, the timing is cleared;

Timing setting:
* After setting the parameter values in the mode selection screen by a short press STOP button, select the time range;
* XXX decimal point bits, timing range: 1 second to 999 seconds
* XX.X decimal point in ten, Timing range: 0.1 seconds to 99.9 seconds
* X.X.X. decimal full brightness, Timing range: 1 minute to 999 minutes
* For example, you want to set up OP is 3.2 seconds, then move the decimal point to ten, the digital display 03.2
* Parameter Description: OP-time, CL off time, LOP cycles (1-999 times, "---" represents infinite loop)
* These parameters are independent of each other, but each of these common mode parameters, for example, P1.1 set OP-time is 5
seconds, the user wants to switch to P1.2 mode, then enter P1.2 set the appropriate parameters, OP It will be five seconds;
* In the main interface (display 000) Press SET button will display OP (CL, LOP) and the corresponding time XXX;
* If only OP mode (such as the mode P1.1, P1.2, P1.3) time, then press SET button will display only the OP and the corresponding
time;
* If the pattern has OP, CL, LOP (such as the mode P3.1, P3.2) then press the SET button OP and the corresponding time, CL and
the corresponding time, LOP and the corresponding number will be displayed;
* In the set mode, the main interface parameters by a short press the SET button can easily see the current mode set in, very
convenient!


Parameter Settings:

* First, determine the operating mode of the relay;
* The mode of operation of the relay, in the main interface (when the module is powered on, flashes the current work mode (P1.1
default mode), then enter the main interface) "long press SET button for 2 seconds after the release "to enter mode selection
screen by press UP, DOWN buttons to select the mode to be set (P1.1 ~ P-4);
* After selecting the mode to be set (for example, P3.2) Press SET key to set the appropriate parameters, then the parameter to
be set flashes (OP-time, CL off time, LOP cycles ( "- - "represents infinite loop)) by UP, DOWN to adjust the value, support
long press (rapid increase or decrease) and press (increase or decrease one unit); setting the parameter value by a short press
STOP button to select the decimal point position, select time range (corresponding time of 0.1 seconds to 999 minutes); short
press sET key to set the next parameter of the current mode, the process above;
* After setting the parameters of the selected mode is good, press the SET button for 2 seconds after release, currently set mode
will flash, and then return to the main screen, set the parameters of success is very simple!
* The main interface: In the relay does not work status display "000" (no decimal point), with a decimal point under relay state,
very clear!
* Mode selection screen: Long press SET to enter, after setting is completed, press SET key to exit and return to the main
interface is very simple!


STOP key functions:

Relays enable mode:
* ON: inner OP-time relay allows conduction;
* OFF: relay prohibit conduction is always closed;
* In the main interface, short press the STOP button to switch between ON and OFF, the current in which the state will flash, and
then return to the main screen. (This feature is an emergency stop function, a key disconnect relay closed)

Sleep mode:
* C-P Sleep mode: five minutes without any operation, the digital display automatically turns off, the normal operation of the
program;
* O-d normal mode: digital display always open;
* Press STOP button for two seconds after the release, to switch C-P and O-d state, in which the current state of flashes and
then return to the main screen.



Product Description




Specification


item
value
Place of Origin
original
Brand Name
Time Delay Relay Module
Model Number
Time Delay Relay Module
Type
relay
Coil Type
---
Coil Current
--
Coil Voltage
---
Contact Form
--
Contact Rating (Current)
-
Switching Voltage
--
Features
---
Mounting Type
Contact customer service
Termination Style
Contact customer service
Operating Temperature
Contact customer service
Circuit
Contact customer service
Current - Output
Contact customer service


Packing & Delivery




box


Company Profile






Shenzhen kaeren Technology Co., Ltd. acting TI NXP ST NXP Atmel TI Microchip and other international brand products.Main wholesale electronic components, MCU, sensors, radio frequency IC, price advantage, quality 100% guarantee!Applications include aerospace, industrial control, ship weapons, satellite equipment, medical electronics, communication electronics, automotive electronics, instrumentation products and other markets.Companies with a number of retailers and agents to establish a long-term stable relationship of cooperation!, the distribution of Hong Kong, Shenzhen, Shanghai and other places of the integrated sales network channels, but also in the delivery and so on and is the world's many famous electronic manufacturers of integrated circuits and electronic components authorized distributor company was established until today has been to the quality of survival, to the reputation of development.Rewards customers with premium prices, which makes us stand out in the industry and become the preferred reliable supplier for customers.With the support of our customers and the fierce competition in the IC market, the company keeps innovating and developing step by step, and enjoys a high reputation in the electronic industry.There are more than 500 stable purchasers in our company. We will provide you with all-round services such as "core" for "heart". We sincerely cooperate with suppliers, distributors and manufacturers at home and abroad to make contributions to the development of the electronic industry.Company tenet: credibility first, genuine, quality service, notarial transactions.


FAQ


1. who are we?
We are based in Guangdong, China, start from 2019,sell to Eastern Europe(20.00%),North America(20.00%),Mid East(10.00%),Oceania(10.00%),South America(10.00%),Southeast Asia(10.00%),Central America(10.00%),Africa(5.00%). There are total about 51-100 people in our office.

2. how can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;

3.what can you buy from us?
electron component,sensor,capacitor,connector,module

4. why should you buy from us not from other suppliers?
Shenzhen carn Technology Co., Ltd. acting TI NXP ST NXP Atmel TI Microchip and other international brand products.Main wholesale electronic components, MCU, sensors, radio frequency IC, price advantage, quality 100% guarantee!Applications include aerospa

5. what services can we provide?
Accepted Delivery Terms: FOB,CFR,CIF,EXW,FAS,CIP,FCA,CPT,DEQ,DDP,DDU,Express Delivery,DAF,DES;
Accepted Payment Currency:USD,EUR,JPY,AUD,HKD;
Accepted Payment Type: T/T,MoneyGram,Credit Card,PayPal,Western Union,Cash,Escrow;
Language Spoken:English,Chinese


0.0475 s.