Антикоррозийный кабельный лоток из стеклопластика FRP шириной 200 мм, 300 мм, 400 мм, 500 мм

Share on:


Price:
Price in USD:Details

Quantity:


Product Overview

Description


Anti-corrosion 200mm 300mm 400mm 500mm Width Fiberglass FRP Cable Tray



Product Description


_02


FRP cable tray 


FRP cable tray is divided into ladder type cable tray, trough type cable tray and tray type cable tray. FRP cable tray is an automated production process in which untwisted glass fiber and other continuous reinforcement materials, polyester, flame retardant materials, surface mats, etc. are impregnated, passed through the cable tray forming mold, and cured at high temperature in the mold, and then continuously ejected from the mold. . The pultruded fiberglass cable tray has the characteristics of light weight, flame retardant, anti-corrosion, immersion resistance, and high mechanical strength. When users lay cables and require shielding performance, our company clamps mixed pultrusion of cast titanium steel mesh or copper mesh to enhance the anti-interference ability of the power supply. The load capacity of the pultruded glass fiber reinforced plastic cable tray is similar to that of the original steel tray of the same specification. The weight is a quarter of the copper bridge. Corrosion resistance is ten times that of copper. Therefore, it is widely used in petroleum, chemical, textile, light industry, metallurgy, machinery, electric power, communication, underground garage, subway and national defense engineering indoor and outdoor cable laying, power supply and cable tunnels, etc. Series of cable trays are suitable for electric power with voltage below 10KV Laying of cables and control power supply, lighting wiring, pneumatic and hydraulic pipelines.


4.jpg





Product Show


 


photobank-(30)_01.jpg


photobank (6)photobank (4)


photobank-(30)_02.jpg


 (17)


Installation:


The installation of the cable tray can be adapted to local conditions, and can be laid according to the technological requirements, such as pipe laying, floor slabs, under-beam lifting, indoor and outdoor walls, beam walls, tunnels, and cable trench walls. It can also be installed on outdoor columns.


—When the height of the bridge slot is 50, 100mm, each end has 6 connection holes, and when the height is 150, 200mm, each end has 12 connection holes.


—Support spacing: the support spacing should be less than or equal to the load curve allowable load and support span.


—Bridge width: When selecting the width of the cable bridge, a certain amount of spare space should be left in order to add cables in the future.


—Separate laying: When there are few power cables and control cables, they can be installed in the same cable tray, but the power cables and control cables must be separated and laid by partitions in the middle.


—Cable fixation: When the cable trays are laid horizontally, the connection between the trays should be set at 1/4 as far as possible. The horizontal cables are fixed every 2 meters, and the vertical cables are fixed every 1.5 meters.





Product Application


_08


Matters needing attention


—The cable tray must be protected by a cover plate within two meters of the ground.


—Places vulnerable to mechanical damage must be protected by cover plates.


—When the cable tray is erected horizontally, the best span support should be selected according to the load curve. When the cable tray is erected vertically, there must be a fixed frame every 1 meter or 2 meters to ensure the stability of the cable tray.


—When the cable is led horizontally and vertically from the cable tray, a guide plate should be installed to protect the cable from damage.


—Under normal circumstances, the steel cable tray should be reliably grounded to form an electrical path, and the cable tray should be connected to the grounding trunk of the workshop.


—In a corrosive environment, non-steel cable trays should be laid along the edge of the cable tray with 12*4 aluminum plates or 12*4 flat steel as grounding wires.


—Cable trays are not allowed to be used as pedestrian passages and standing platforms.





Related Products


_10





Company Information


1_11.jpg


1_12.jpg 





Packaging & Shipping








FAQ









Q: Are you a trading company or a manufacture factory?


A: Our factory is one of the biggest FRP products, FRP machines manufacturer in China.


 


Q: Can your factory customize the FRP products for clients ?


A: Yes, we can.We have a senior designer, can help customers make CAD drawings.


 


Q: How about after-sales service ?


A: 1 year free warranty, Lifetime technical service support.


 


Q:What's the guarantee, in case the FRP products breaks down?


A: Within the guarantee period stipulated in the contract. If it breaks down, generally speaking, our technician will figure out what the problem may be, according to client s feedback. Parts will be replaced for free if the problems are caused by quality fault.


 


Q: How can I install the production and get a commissioning ?


A: We may send our engineer for installation and commissioning, but relevant cost will be paid by you.


 


Q: Do You Arrange Shipment For The Machines?


A: Yes, dear esteemed customers, for FOB or CIF price, we will arrange shipment for you. For EXW price, clients need to arrange shipment by themselves or their agents.


 



 


 















 


 


 


 


 


 


 


 


 


 


 


 


 


0.0126 s.