Wholesale Price Clear Epoxy Resin Transparent Glue Strong Composite Resin Hot Sale CAS 7085 85 0 Epoxy Resin Casting For Table
- Category: >>>
- Supplier: Jiangyin Xufang Chemicals Co. Ltd.
Share on (1600997207558):
Product Overview
Description
Best Selling
Product Description
Epoxy resin AB adhesive is a high-strength, fast adhesive composed of two components: a epoxy resin and b curing agent. Mixing these two components together in a certain proportion will produce a very strong adhesive force that can quickly bond various materials together.
1.Original product Feature
--Two components of epoxy resin and Hardener with Mix Ratio of 2:1.
--Non toxic, 100% solids, low VOC,low odor.
--Thin liquid easy to handle,automaticly Self-leveling & Anti-foaming.
--Crystal clear,high see through, yellow resistance.
--Excellent color stability with pigments.
--Thick Pour,One-time pouring,up to 2"-4"thick each pour.
2.Curing Effects
--Slow curing, low heat and temperature, up to 2"-4"thick each pour.
--Cured without ripples, Wrinkles,no bubbles.
--Good transparency and excellent surface gloss like mirror.
--Can polish after drying.
--After drying,with high hardness as stones
--Non toxic, 100% solids, low VOC,low odor.
--Thin liquid easy to handle,automaticly Self-leveling & Anti-foaming.
--Crystal clear,high see through, yellow resistance.
--Excellent color stability with pigments.
--Thick Pour,One-time pouring,up to 2"-4"thick each pour.
2.Curing Effects
--Slow curing, low heat and temperature, up to 2"-4"thick each pour.
--Cured without ripples, Wrinkles,no bubbles.
--Good transparency and excellent surface gloss like mirror.
--Can polish after drying.
--After drying,with high hardness as stones
Deep Cast Clear Casting Resin for River Tables
DIY Crafts&Jewelry:
The mixed resin can be readily pigmented by the addition of any resin pigments sold in our online store. It can then be poured into a mould, made of plastic or silicone rubber. Moulding can be carried out by gravity or under vacuum.
River Tables:
Excellent for River,Live-edge& Wood Tables.
Whatever,the emperature should be between 18-25ºC with humidity level below 70%. A 2:1 mix will provide a hard casting suitable for manufacture of fancy shapes, decorative items etc.
Once the resin is mixed and poured into the mould gently pass warm air from a heat gun or hair dryer on slowest speed setting,this will assist in removal of any bubbles generated during mixing.
DIY Crafts&Jewelry:
The mixed resin can be readily pigmented by the addition of any resin pigments sold in our online store. It can then be poured into a mould, made of plastic or silicone rubber. Moulding can be carried out by gravity or under vacuum.
River Tables:
Excellent for River,Live-edge& Wood Tables.
Whatever,the emperature should be between 18-25ºC with humidity level below 70%. A 2:1 mix will provide a hard casting suitable for manufacture of fancy shapes, decorative items etc.
Once the resin is mixed and poured into the mould gently pass warm air from a heat gun or hair dryer on slowest speed setting,this will assist in removal of any bubbles generated during mixing.
Specification
OUR 2:1 FORMULA IS EASY TO MEASURE & EVEN EASIER TO POUR!
DIRECTIONS FOR USE:
Step 1: The ideal working temperature is around 77°F. Best results can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment. Avoid working in high humidity. We recommend using this product on a leveled and flat work surface.
Step 2: Measure product in accordance with your intended use. Prepare 2 parts Base Resin to 1 part Curing Agent by liquid volume.
Pour the Curing Agent first and then the Base Resin into a clean, smooth-sided container large enough to hold all the liquid and allow room for mixing.
Step 3: The material must be mixed thoroughly for at least 6-8 minutes. Be sure to scrape the container sides, bottom, and corners as you mix. Be careful not to whip excessive air into the mixture. If mixing a gallon, use a power mixer set to “hand speed.” For smaller quantities, use stir sticks. Do not mix more than a gallon. Pour into a new, clean container and mix for an additional minute.
Step 4: Pour the mixed resin onto the surface and distribute evenly with a squeegee or gloved hand. Continue to pour remaining material to achieve the desired thickness, allowing the resin to flow evenly over the project’s sides. Resin can be poured up to 2” thick per pour, and up to 4” depending on the volume of the pour.
Step 5: Use a heat source such as a heat gun to remove any bubbles by adding a small amount of heat to the surrounding area. The bubble will rise to the surface and pop.
Step 6: If you are going to make a second pour, the first pour should still be slightly sticky. Once the second pour is made,
bubbles may once again need to be removed. Material will feel hard after 48-72 hours, but full cure and maximum hardness can require up to 7 days, depending upon the temperature.
PRO TIP: If you wish to apply paper decals or other objects under the surface, those objects need to be bonded to the surface either with Epoxy or craft glue. Some wood may take the material well in a single coat; however, many types of wood require a seal coat to prevent air bubbles from rising out of the wood and ruining the surface. Older, more porous pieces of wood may contain both air and moisture that can contaminate the finish. In this case, the user may first paint on a very thin coat of SuperClear Table Top Epoxy, allowing that to set before pouring the new layer.
DIRECTIONS FOR USE:
Step 1: The ideal working temperature is around 77°F. Best results can be obtained at temperatures between 70°F and 85°F, in a clean, dry, dust-free environment. Avoid working in high humidity. We recommend using this product on a leveled and flat work surface.
Step 2: Measure product in accordance with your intended use. Prepare 2 parts Base Resin to 1 part Curing Agent by liquid volume.
Pour the Curing Agent first and then the Base Resin into a clean, smooth-sided container large enough to hold all the liquid and allow room for mixing.
Step 3: The material must be mixed thoroughly for at least 6-8 minutes. Be sure to scrape the container sides, bottom, and corners as you mix. Be careful not to whip excessive air into the mixture. If mixing a gallon, use a power mixer set to “hand speed.” For smaller quantities, use stir sticks. Do not mix more than a gallon. Pour into a new, clean container and mix for an additional minute.
Step 4: Pour the mixed resin onto the surface and distribute evenly with a squeegee or gloved hand. Continue to pour remaining material to achieve the desired thickness, allowing the resin to flow evenly over the project’s sides. Resin can be poured up to 2” thick per pour, and up to 4” depending on the volume of the pour.
Step 5: Use a heat source such as a heat gun to remove any bubbles by adding a small amount of heat to the surrounding area. The bubble will rise to the surface and pop.
Step 6: If you are going to make a second pour, the first pour should still be slightly sticky. Once the second pour is made,
bubbles may once again need to be removed. Material will feel hard after 48-72 hours, but full cure and maximum hardness can require up to 7 days, depending upon the temperature.
PRO TIP: If you wish to apply paper decals or other objects under the surface, those objects need to be bonded to the surface either with Epoxy or craft glue. Some wood may take the material well in a single coat; however, many types of wood require a seal coat to prevent air bubbles from rising out of the wood and ruining the surface. Older, more porous pieces of wood may contain both air and moisture that can contaminate the finish. In this case, the user may first paint on a very thin coat of SuperClear Table Top Epoxy, allowing that to set before pouring the new layer.
Product name | Proportioning | Hardness | Transparency | Antifoam performance | Applicable scenarios/ products | Features |
901 Conventional crystal drop glue | 3：1 | High | High | Good | Products with a thickness of no less than 5mm | Cheap, non-toxic odor, high transparency and yellow resistance |
902 High hardness and high transparency drip glue | 3：1 | Very high | Very high | Good | Applicable to products below 3CM | High hardness, resistance to yellowing, and high transparency |
903 Quick fix high hardness drip glue | 3：1 | Very high | Very high | Good | Small, thin, very small ornaments | High hardness, resistance to yellowing,and quick fixation |
908 Soft glue drip glue | 3：1 | High | High | Good | Drip glue, phone case, elastic cat paw | Hardness 50A, resistance to yellowing, UV resistance test |
911 Ultra clear art resin | 1：1 | High | Very high | Very good | Crystal porcelain painting, artistic resin painting, various handicrafts | Long operational time, odorless, international standard |
909 Thick injected river table resin | 3：1 | Very high | Very high | Good | Suitable for large river tables with a size of 3-5cm (one-time pouring of 3-5cm) | Making a table saves 3 working hours and allows for a large amount of pouring without glue |
906 River table resin | 2：1 | Very high | Very high | Good | Suitable for 1-3cm ordinary river tables | High hardness, high transparency，and resistance to yellowing |
919 High temperature resistant resin | 4：1 | Very high | High | Good | Suitable for high-temperature resistant products, optional for customized temperature resistance of 80 ° C~200 ° C | High tech barriers perfectly replace high priced foreign products |
SX-713AB Adhesive stone adhesive | 3：1 | High | High | Good | Adhesive building colored stone series adhesive additives，suitable for outdoor use | High hardness, high transparency，and resistance to yellowing |
Packing & Delivery
To better ensure the safety of your goods, professional, environmentally friendly, convenient and efficient packaging services will be provided.
Company Profile
Jiangyin Xufang Chemical Co., Ltd. is located in Jiangsu, China,which is known as the "water town in the south of the Yangtze River".The company was established on December 30, 2010 with a registered capital of 1 million (RMB) and nearly 200 employees.It is located in Jiangsu Province，Jiangyin City, covers an area of 200 acres, and another larger factory is located in Gansu Province, and is still expanding.
Mainly engaged in the production and sales of glass fiber, epoxy resin, unsaturated polyester resin, methyl acetate,cyclohexanone, n-butanol and other related series of chemical products, with a complete sales network, fast logistics services,and deep cultivation of new materials industry, and actively expand domestic and foreign business.
FACTORY
EQUIPMENT
LABORATORY
Why Choose Us
Q1 | Who are we? |
A1 | We are based in Jiangsu, China, start from 2010,sell to Eastern Europe,South America,North America,Southeast Asia. There are total about 200 employees. |
Q2 | How can we guarantee quality? |
A2 | Always a pre-production sample before mass production; Always final Inspection before shipment; |
Q3 | What can you buy from us? |
A3 | Resin, fiberglass products, intermediates, organic solvents, cosmetic raw materials, etc |
Q4 | Why should you buy from us not from other suppliers? |
A4 | We have more than 10 years experiences in chemical. We are mainly engaged in the production and sales of glass fiber, resin and methyl acetate. If you have any questions, please feel free to contact us. |
A5 | What if products have some quality problems? |
A5 | This situation rarely happen due to we have very very restrict quality control on every products. Contact us immediately and webelieve we can solve it out with your satisfaction. |
Exhibition Photos
Contact
We Recommend
New Arrivals
New products from manufacturers at wholesale prices
