Fin Press line

Product Overview

Description

 

1 Fin pressing specifications

 

1.1 Type: YKC-24-63, four-uprights single-point

 

1.2 Capacity: 630KN

 

1.3 Strokes per Minute: 150-300spm

 

1.4 Stroke of Slide: 40mm

 

1.5 Die Height Adjustment: 50mm

m

1.6 Slide lifting Height (at min die. height): 80mm

 

1.7 Die Height: 260-310mm ( fulfill the die setting requirements )

 

1.8 Size of table: 900x1350mm ( fulfill the die setting requirements )

 

1.9 Bottom size of slide: 800x890mm

 

1.10Feed exchange structure, Feeding Length: 0-80mm

 

1.11 Fin Parameter: The buyer supply the drawing

 

1.12 With scrap case

 

1.13 With photo-electric safe protector

 

1.14 With scrap blowing unit

 

1.15 Provide 4pcs vibration pads

 

 

 

2 Uncoiler Specifications

 

2.1 Type: Single Head Cradle of Inner distended type

 

2.2 Material: Aluminum Coil

 

2.3 Max. Outer Diameter of Coil: Φ1000mm

 

2.4 Inner Diameter of Coil: Φ150±5mm

 

2.5 Max. width of coil: 550mm

 

2.6 Coil Mounting Direction: The same as the operation panel’s direction

 

2.7 Uncoiler Sensor—photoelectrical sensor type

 

2.8 No Coil Check—photoelectrical sensor type

 

 

3 oil tank and conductor

 

3.1 Type: oil-bathed type

 

3.2 Max. width of coil:550mm

 

3.3 Conductor type: Slip type (Bolt fixing type)

 

3.4 Detect the fin oil: alarm for no oil

 

3.5 Material suppressed type: with coarse cotton cloth

 

 

4. Fin sucked unit

 

4.1 Type: sucked automatically by vacuum air

 

4.2 Sucking length: 1000mm

 

4.3 Controlling type: the unit is driven by air cylinder, the sucking power is adjusted by the mean of a convertor

 

4.4 Sucking plate: Aluminum

 

4.5 Adjustment of sucking unit: The unit can be adjusted on up-down, left-right and front-rear directions

 

 

5 Collection unit

 

5.1 Type: two seat rotary device (can move left and right)

 

5.2 Collecting height: 720mm

 

5.3 Fin length: 1000mm

 

 

6 Electrical system

 

6.1 Type: stand-up electrical box, movable operation panel

 

6.2 Power voltage: any

 

6.3 Crossing notch: count periodically, air cylinder is controlled by the electrical part

 

6.4 End notch: count periodically, air cylinder is controlled by the electrical part

 

6.5 Middle notch: count periodically, air cylinder is controlled by the electrical part

 

6.6 Sewing-machining cut: count periodically, air cylinder is controlled by the electrical part

 

6.7 Program Change System: changeable for 2P to 1P,

 

6.8 Stow-stopping Circuit: count periodically

 

6.9 Air pressure requested: 5Kg/cm2(+10%)

 

6.10Air consumption: 700L/min

 

6.11 The fin press will stop automatically once there is on material, alarm of collection and insufficient pressure of hydraulic system.

 

6.12 The human/machine interface will show the alarm content

 

 

 

7 others

 

7.1 Color: according to the seller’s catalogue

 

7.2 Power supply and air pipe: according to the buyer’s requirement

 

7.3 Foundation: supply a foundation drawing

 

7.4 Manual: supply one English manual copy

 

7.5 Spare parts: see the packing list

 

(1) Foundation Bolts (2) Expansion Bolts

 

(3) Y Seal Ring UHP200 (4) Y Seal Ring UN035

 

(5) Manual Grease Adding Gun

 

7.6 Main Components List

 

1 Dual electromagnetic valve for clutch made by ROSS

 

2 PLC controller made by MITSUBISHI

 

3 Frequency Converter made by MITSUBISHI

 

4 Main pneumatic valves made by FESTO (Germany) or SMC(Japan)

 

5 Main electrical components made by TELEMECANIQUE (France)

 

6 Hydraulic pump Taiwan

 

7 Hydraulic valve made by ATOS (Italy)or Taiwan

 

8 Bearing for feeder change unit made by IKO (Japan)

 

9 Encoder made by MITSUBISHI

 

10 Toucher interface made by MITSUBISHI

 

11 Auto grease pump made by IHI(Japan)

 

12 No material testing sensors made by OMRON

 

13 Change switch made by TELEMECANIQUE

 

14 AC Contactor made by TELEMECANIQUE

 

15 Main button switch made by IDEC(Japan)

 

16 Indicator light made by XB2(Japan)

 

17 Breaker made by ABB

 

18 Output relay made by Carlo Gavazzi(Swiss)

 

7.7 Oil-moisturizing ports

 

A ports for punching hole and trimming edge: each on both sides( used for lubricating and blowing scrap)

 

B ports for drawing: each on both sides( used for lubricating)

 

C ports for slitting: each on both sides(used for lubricating)

 

D ports for reflare: each on both sides(used for lubricating)

 

7.8 Pressure Air Ports

 

A ports for compressing material—usually opened, set on the operating side

 

B ports for end cutting cylinder—each on both sides

 

C ports for special shape cutting cylinder—each on both sides

 

D ports for middle cutting cylinder—each on both sides

 

 

7.10 Supply the fin drawing within one week after conclude the contract(including fin hole diameter, distance between row, distance between hole, outer collar size, collar height, fin length ), supply die fixing specification, material-setting position, sealing height, lubricant connecting position and so on.

 

 

8 Acceptance standard

 

8.1 15 days before the delivery time, the seller should notify the buyer to send the die, material, fin oil to the seller’s factory for installation and training.

 

 

8.2 Acceptance standard: should be suitable for the technical agreement and fit for the fin die to produce the qualified products.

Acceptance site: the seller’s factory

 

 

9 Guarantee time

 

One year after acceptance of installation and training

 

 

10 After sale service

 

10.1 The seller supply the after sale service forever, and free of charge within the guarantee time

 

10.2 After the guarantee time, the seller provide the spare parts at cost price

 

 

All disputes, claims or matters of breach or non performance arising out of this contract shall be resolved by negotiation

 

Technical Agreement for Fin Die