The hot air enters the mixing and pulverizing drying chamber from the bottom of the dryer at a suitable spouted speed from the inlet tube, resulting in strong shearing, collision, friction and particle transformation of the material, which strengthens the mass transfer and heat transfer.
Product Description
Product Description
Working Principle:
At the bottom of the dryer, the larger and wetter particles were broken by machinery under the action of the agitator, the wet content was lower, and the particles with smaller particle size were entrained by the rotating air flow, which were further dried during the rising process. Because of the rotating flow of gas-solid phase, the inertia of solid phase is greater than that of gas phase, the relative velocity between the two phases is larger, and the mass transfer and heat transfer between the two phases is enhanced, so the production intensity of the machine is high.
Product Features:
1. A variety of feeding devices for selection, feeding continuous stability, the process will not produce bridging phenomenon.
2. A special cooling device is installed at the bottom of the dryer to avoid the deterioration of the material in the high temperature area of the bottom.
3. Special pneumatic seal and bearing cooling device, effectively extend the service life of transmission part.
4. The special air-dividing device reduces the resistance of the equipment and effectively provides the handling air set of the dryer.
5. The drying room is equipped with grading ring and swirl sheet, material fineness and final moisture can be adjusted (if the final water content of calcium carbonate can be adjusted to ≤ 0.1%).
6. Compared with other drying methods, it can effectively increase the specific gravity of materials.
7. High circumferential gas velocity and short residence time in the drying room, which can effectively prevent the material from sticking to the wall and heat sensitive material deterioration, and achieve high efficiency, fast, small equipment and large production.
Packing & Delivery
Packing & Delivery
1. Our XSG series spin flash dryer in flash drying equipment should been cleanned first, then packaged with the transparent coating, next it will been shipped into the marine container with steel wire fixing.
2. If there is over-size drying machine, we will choose the flat rack container to shipping. First by road to Shanghai port or other port as customers' needs, then by sea.
3. The contract takes effect after receiving 30% advance payment; Delivery within 15days after receiving the another 70% of the total value of the product.
Our Service & FAQ
Our Service
Pre-service: As a good and rich experience supplier, we should offer customer the best quality and best price of the machine. We do something as following:
(1). introduce the suitable product to the customer in detail
(2). answer the question raised by customer carefully
(3). make the suitabe project as the customer requirement
(4). make sure the machine is suitable for the material
Sale service:
In order to fulfill the contract smoothly, establish a good cooperative relationship, here's are several points what we must do. (1). ensure product with high quality and pre-commissioning before delivery (2). delivery on time (3). provide full set of documents as customer’s requirements
After-sale service: Provide considerate services to minimize customers’ worries. (1). Assist customers to prepare for the first construction scheme. (2). Install and debuging the drying equipment. (3). Train the first-line operators. (4). Exame the drying equipment. (5). Take initiative to eliminate the troubles rapidly. (6). Provide technical support. (7). Establish long-term and friendly relationship with all my customers.
Service commitment: We provide customers 12-months warranty to make sure the machine work well, and always keep certain inventory level of spare parts, which means the replacements can be sent to you timely. At the same time, we send every customer a preferential and reasonable quotation.
FAQ
Q: How can i visit your factory? A: Our company is in Changzhou city, and it is very near Shanghai city. It takes about 1 hour to get to Changzhou. Or we can even visit you in Shanghai.
Q: Are you a factory or a trading company?
A: We are a manufacturer, and have been in the drying industry for more than ten years.
Q: What’s the MOQ of your products? A: 1 set.
Q: How is the quality of your products? A: Our products come with best quality, and passed CE certification. And exported to lots countries around the world, such as Australia, Malaysia, Korea, Brazil, Argentina, Russia, South Africa, etc. You can rest assured with the quality absolutely.
Q: What to do if the drying machine has a problem? A: 24 hours timely response of mail and phone calls. If the parts broken belong to non-artificial factors within 12 months, we offer free replacement. If beyond 12 months, customers should bear the freight back and forth and accessories cost.
Q: Does your price include freight? A: The price we offer usuallly is FOB Shanghai price. If you request CIF, please give us your delivery port, and even can offer the EXW price (the machine cost) for you.
Q: What is the payment term you prefer? A: Our usual payment term is T/T. 30% T/T in advance, another 70% T/T before shipment. Other ways can also be received after we discussion and agreement, like L/C.
Q: Which kind of payment you accept?
A: Common is after 30% of the advance payment is received, the contract becomes effective (20% of which is the deposit); The production cycle depends on the actual situation; Delivery to Shanghai port within 15 days after the another 70% payment is received.
Important Notice
In order to quote you the right drying machine equipment with best price, we would like to get the following information include in your inquiry.
