Share on (60840566731):
Defibrillator Monitor DM7000
Weight: 20 pounds (9.9 kg) (basic configuration).
Size: 13 x 9.6 x 7.2 inches (33 x 24 x 18 cm).
Operating:
Temperature*: 0 to 40° C
Humidity* (NC): 15 to 95% RH
Altitude: Up to 4572 M (15,000 feet)
Transport and Storage:
Temperature: -20 to 55°C
Humidity: 15 to 95% RH (non-condensing)
Atmospheric pressure: 860 to 1060 hPa
Shock/vibration: ISTA 1A
Water: IEC 529, IPxx.
Operating Power: Ni-MH 12 volt - M&B
Category | Parameter | |
Waveform: | Truncated Exponential Biphasic | |
Output Energy Accuracy: | +/- 15% or 1J (whichever is greater) at 25 to 175 ohms | |
AED Energy Sequence | 150, 200J(twice) 150, 150, 200J(three times) 150,150, 150, 200J(Four times) | |
manual mode | ||
no battery, 100% AC mains voltage,charge to max energy(360J) | <9 seconds | |
New battery, ,charge to max energy(360J) | <14 seconds | |
no battery, 90% AC mains voltage,charge to max energy(360J) | <9 seconds | |
with a Ni-MH 12 volt - M&B battery after 15 discharges, charge to max energy(360J) | <15 seconds | |
no battery, 90% AC mains voltage,from system on to charge max energy complete | <20 seconds | |
with a Ni-MH 12 volt - M&B battery after 15 discharges, from system on to charge max energy complete | <25 seconds | |
AED mode | ||
no battery, 100% AC mains voltage,charge to max energy(200J) | <7 seconds | |
New battery, ,charge to max energy(200J) | <9 seconds | |
no battery, 90% AC mains voltage,charge to max energy(200J) | <7 seconds | |
with a Ni-MH 12 volt - M&B battery after 15 discharges, charge to max energy(200J) | <10 seconds | |
no battery, 90% AC mains voltage,from system on to charge max energy complete | <25 seconds | |
with a Ni-MH 12 volt - M&B battery after 15 discharges, from system on to charge max energy complete | <28 seconds | |
Analyzing time | 9 seconds | |
| ||
The Maximum Voltage | 1340±50V | |
Defibrilator Resistor range | AED mode | 20Ω to 200Ω |
Manual mode | 20Ω to 1500Ω | |
Synchronous delay time | <60ms
| |
1) Heart Rate meter range and Accuracy: 27 to 300 BPM. ±3 per/min
2) Electrosurgery protection:
The HF SURGICAL EQUIPMENT which is used comply with IEC 60601-2-2 and shall have a minimum power cut mode capability of 300 W, a minimum coagulation mode of 100 W and working frequency of 400 kHz ±10 %.
3) input circuit loop leak current: <0.1μA;
4) Tall T-wave rejection capability:<0.8mV
5) Heart rate averaging:3 times.
6) Heart rate meter accuracy and response to irregular rhythm.:
indicated heart rate: 80bpm,60bpm,90bpm,, after a 20 s EQUIPMENT stabilization period, for the four types of alternating ECG complexes A1 to A4 described in Figure 101.
7) Response time of heart rate meter to change in heart rate: <10s
8) Time to ALARM for tachycardia:<6s
9) auditory alarm:
High alarm frequency : 0.125Hz
Low alarm frequency : 0.042Hz
10) Visual alarm:
High alarm: red LED flashing, and the flashing frequency is 2Hz
Low alarm : yellow LED always light on.
11) Pacer pulse detection disabling
Pace Detect switch:On/Off.
12) Display
The available time displays of the equipment: always.
13) The input impedance:>5Mohm(within a d.c. offset voltage range of ±300 mV)
14) Recovery time from electrode polarization after defibrillation:<10s





Certificates


New products from manufacturers at wholesale prices