2BV чугунный циркуляционный насос промышленный жидкостный вакуумный кольцевой

Сохранить в закладки 1601160662815:


Цена:350,00 $*

Количество:

  • В избранное

Описание и отзывы

Характеристики





1、 Product overview

As a new generation product, 2BV water ring vacuum pump will replace SK, 2SK series water ring vacuum pump and W, WY, WL series reciprocating vacuum pump with excellent performance and many advantages.

2、 Product features


The mechanical seal of 2BV water ring vacuum pump is imported, and the seal can be made of fluororubber or polytetrafluoroethylene
Compared with the same type of domestic SK, 2SK, SZ Water ring vacuum pump, it has the following characteristics:
·2BV water ring vacuum pump is designed with coaxial direct connection, which saves space and is easy to install.
·2BV water ring vacuum pump adopts imported mechanical seal as standard configuration.
·2BV water ring vacuum pump is equipped with cavitation protection pipe interface. If it works under pressure, opening the cavitation protection pipe interface (or connecting with the separator) can eliminate the cavitation sound under the condition of limited suction effect and protect the pump.
·Aluminum bronze impeller has high strength and durability, and enhances the corrosion resistance of 2BV water ring vacuum pump. If the flow passage parts are made of stainless steel, they can work in more severe environment.
·Flexible exhaust port design, no over compression, 2BV water ring vacuum pump in its performance range of high efficiency.
·Y2 series motor with protection grade of IP54 and IP55 (common IP44)
·2BV water ring vacuum pump adopts NTN or NSK imported bearing

3、 Scope of application

2BV water ring vacuum pump is suitable for removing gas and steam. The suction pressure can reach 33 mbar (97% vacuum degree). When transformer oil is used as working fluid (called oil ring vacuum pump), the suction pressure can reach 6.7mbar (99.3% vacuum degree), which can completely replace the reciprocating vacuum pump. When the liquid ring vacuum pump works for a long time under the suction pressure close to the vacuum, the cavitation protection pipe should be connected to protect the pump and eliminate the cavitation sound. When used as a compressor, the pressure is up to 0.26mpa. When used as a compressor, the power of 2BV pump will be caused by the increase of discharge pressure. When ordering, the discharge pressure should be indicated to select the appropriate motor power.
2bv2 ex and 2bv6 series water ring vacuum pumps / compressors are mainly used to remove gas and work in various flammable and explosive environments. Their performance parameters are the same as those of 2bv2 and 2bv5 series.
2BV series stainless steel vacuum pump can be used in various occasions with high corrosion resistance and cleanliness requirements. According to the working conditions, the flow passage parts of 2BV series stainless steel vacuum pump: pump body, pump cover, disc and impeller can be made of SUS304 (0Cr18Ni9), SUS316 (0Cr17Ni12Mo2) and SUS316L (00Cr17Ni14Mo2), and the material of pump shaft is 2Cr13 or 0Cr18Ni12Mo2Ti


























Who is the trouble of 2BV vacuum pump
Who is 2BV vacuum pump or the possible cause of failure
Who is 2BV or vacuum pump to eliminate the reason
The motor does not start and there is no sound

Two power lines are broken

Check wiring
The motor does not start, there is a buzzing sound
1.One wiring is broken and the motor rotor is locked.
2. Impeller failure. 
3.Motor bearing failure
1.Drain clean pump if necessary and correct impeller clearance. 
2.Change impeller. 
3.Replace the bearing
When the motor starts, the current circuit breaker trips
1. The winding is short circuited. 
2. Motor overload. 
3. The exhaust pressure is too high.
4. Too much working fluid
1. Check the motor winding. 
2. Reduce the flow rate of working fluid.
3. Reduce the exhaust pressure. 
4. Reduce the working fluid
Excessive power consumption
              Precipitation is produced
             Clean and remove sediment

No vacuum is produced
1. No working fluid 
2. Serious system leakage 
3. The rotation direction is wrong
1 check the working fluid 
2. Repair the leak 
3. Change two wires to change the direction of rotation



The vacuum is too low
1. The pump is too small 
2. The flow rate of working fluid is too small 3. The working fluid temperature is too high (less than 15
℃) 
4. Corrosion 5. Slight system leakage 6. Seal leakage
1. Use a larger pump 
2. Increase the flow rate of working fluid 
3. Cool the working fluid and increase the flow rate 
4. Replace  parts 
5. Repair the leak 6. Check the seal

      Sharp noise
1. Cavitation 
2. The flow rate of working fluid is too high
1. Connect the gas shield 
2. Check the working fluid and reduce the flow rate
            leakage
           The sealing gasket is damaged
                Check all sealing surfaces








1、 Product name and model ① caliber ② head (m) ③ motor power (kw) ④ flow rate ⑤ rotational speed ⑥ voltage (⑦ suction lift) whether the medium has accessories, so that we can correctly select the type for you
2、 If our company's product model has been selected by the design unit, please send it to our company for purchase directly.
3、 When the use environment is very important or complex, please provide design drawings and detailed parameters as far as possible, and our company's technology will check for you.

Product price attribute is for reference only, please call Wangwang for details!






Похожие товары

Новые поступления

Новинки товаров от производителей по оптовым ценам