Главная
Все Категории
T5 T8 ультрафиолетовая бактерицидная uvc балластная лампа электронные световые балласты 230 В 50 Гц 60 Вт Ультрафиолетовый балласт с таймером

T5 T8 ультрафиолетовая бактерицидная uvc балластная лампа электронные световые балласты 230 В 50 Гц 60 Вт Ультрафиолетовый балласт с таймером

Категория: >>>
Поставщик: Jiangsu Pei De Water Treatment Equipment Co. Ltd.

Цена:2 187,87 ₽ - 4 375,74 ₽*

Количество:

В избранное

Описание и отзывы

Характеристики

Product Paramenters

Electronic ballast for uvc lamp

1. Brief Introduction
LPCU-1PH-A-3 is a high frequency electronic ballast, with high performance. It starts and drives middle pressure gas discharge lamp, which has dimming control system as well. How do it works shows at below:

2.Working conditions

Environment temperature:-5℃~+5
Relative humidity :≤95%
Altitude≤1500M
Meet IEC61373-2010 standard requirement

3.Electric parameters

LPCU-1PH-A-3
Lamp power(max) (Output power)	3kW
Lamp voltage (Output voltage)	300V-500V (depend on the lamp)
output current	<8.6A
Input voltage	206-278VAC,single phase
Input current	17A(Max)typical valve
Input frequency	46-63Hz
Power factor	0.98(Typical value)
Efficiency	>94%(Typical value)
Harmonic current distortion	<5%(Typical value)
Range of output power	15%-100%
Output frequency	40-200kHz
Ignition voltage	1650Vp
Protect function	Output short circuit protection,Open load protection,Output over voltage protection,Input over voltage protection,Input undervoltage protection,high temperature protection
Lamp monitor	Current Monitor,voltage monitor
Control way	IO(Compatible with PLC), CAN open, RS485(MODBUS)
Working environment temperature	-5℃~+55℃
High humidity	90%
Cooling way	Forced air cooling,water-cooling
Protection class	IP20
Size	32913565
Weight	4kg

4. Electrical interface

1.Input port

Connector:PC 5/ 3-STF1-7,62 – 1777846

2.Output port

Connector:PC 5/ 3-STF1-7,62 – 1777846

3.Control port A

Connector:Phoenix MC 0,5/8-G-2,5
Connected with PLC IO,Read “5-control way”

4.Control port B

Connector:Phoenix MC 0,5/7-G-2,5
CAN BUS, RS422/RS485 Communication interface. Read “5-control way”

5.Control way

This Model ballast has three control ways of PLC I0 Hard wire, CAN Bus communication, RS485/RS422 BUS Communication, chosen by
code switch.

As code switch shows above, it stands for number 17.

Number meaning on Code switch

Code switch value	Control way
0	hard wire control
Non O	CAN bus/RS422 bus communication control Code switch value is the communication address

1.Hard wire control
Control port A connected with IO of the PLC,using the PLC to control the ballast.

1.1 pin definition

Pin	Function	Direction	Type	Description
1	PLC COM (0V)	Input	0V	the cathode of external power
2	Must Dangling
3	Fault code 1	Output	Open connector	Low level means fault(driver fault)
4	Fault code 2	Output	Open connector	Low level means fault(system fault)
5	Fault code 3	Output	Open connector	Low level means fault(indicator light fault)
6	START/STOP	Input	24V	The anode of external power
7	Lamp light on signal	Output	Open connector	Low level means lamp works
8	Dimming control	Input	PWM	Duty ratio controls power

1.2 Controller PLC connecting wire grid

1.3 lighting
1.3.1 Control port A Pin 6 connect with 24V, ballast starts output.
1.3.2 lights on all, control port A Pin 7, output low level

1.4 Dimming control
Exterior PWM signal enters into Ballast, ballast starts dimming control. PWM signal frequency scale: (1KHZ-3KHZ)

PWM Duty ratio	Lamp Power
<10%	450W
10%	450W
97%	3000W
100%	3000W

2.CAN bus control way
Read “LPCU-1PH-A-3 CAN OPEN”protocol

3.RS422/RS485 bus control way
Read “LPCU-1PH-A-3 MODBUS”protocol

6. LED lamp indication
The ballast has five led indicator lights.

Name	Description
RUN	Supply power, “RUN” Lights on, ballast operates.
LAMP	Indicator light flashes, lamp is on the process of lighting on. Indicator light on stably, lamp finishes starting. Indicator light off, lamp off.
FAULT	Indicator light on, fault happens. (Ballast default or lamp default)
TX	Indicator light flashes, communication data is sending. (CAN BUS OR RS485 BUS) Indicator light doesn’t flash, no data is sending.
RX	Indicator light flashes, communication data is accepting. (CAN BUS OR RS485 BUS) Indicator light doesn’t flash, no data is accepting.

7.Dawing of overall dimensions

Production Process

Company Profile

FAQ

1. Q: What terms of payment do you accept?

A: Payment method:T/T,Paypal,western union.

2. Q: What is your delivery time?

A:Delivery term:10-30 working days.

3. Q: What's the minimum quantity of your order?

A: MOQ:1 Set.

4. Q: How long is the warranty?
A: Quality guarantee period:1 year

Новые поступления

Новинки товаров от производителей по оптовым ценам