Software release

• Junos OS Release 15.1F5 and 15.1F6, Junos OS Release 17.1R1 and later

  For information about which MPCs support this MIC, see MIC/MPC Compatibility. For information about which MICs are supported on MX Series routers, see MICs Supported by MX Series Routers.

Description

• One 100-Gigabit DWDM OTN port
• Power requirements (including transceiver) at different temperatures:
  • 55° C: 1.90 A @ 48 V (91 W)
  • 25° C: 1.73 A @ 48 V (83 W)
• Weight: 2.3 lb (1.04 kg)
• Model number: MIC3-100G-DWDM
• Name in the CLI: 1X100GE DWDM CFP2-ACO

Hardware features

• Dual-wide MIC that installs into two MIC slots
• Supports CFP2 analog coherent optics (CFP2-ACO)
• Transparent transport of a 100-Gigabit Ethernet signal with OTU4V framing
• ITU-standard OTN performance monitoring and alarm management
• Dual-polarization quadrature phase shift keying (DP-QPSK) modulation

• Supports three types of forward error correction (FEC):

  • Soft-decision FEC (SD-FEC)
  • High-gain FEC (HG-FEC)
  • G.709 FEC (GFEC)
• 100 channels on C-band ITU grid with 50-GHz spacing

• Latency:

  • SD-FEC: 14 µs (TX + RX)
  • HG-FEC: 22 µs (TX + RX)
  • GFEC: 6 µs (TX + RX)
• Interoperable with the CFP-100GBASE-ZR transceiver supported on the 100-Gigabit Ethernet MIC with CFP (MIC3-3D-1X100GE-CFP) on MX Series routers and the 100-Gigabit Ethernet PIC with CFP (P1-PTX-2-100GE-CFP) on PTX Series routers.
• Interoperable with the 100-Gigabit DWDM OTN PIC with CFP2 (PTX-5-100G-WDM) on PTX Series routers when the 100-Gigabit DWDM OTN MIC is configured to use SD-FEC or GFEC.

Note: The 1-port 100-Gigabit DWDM OTN MIC is not directly interoperable with the 2-port 100-Gigabit DWDM OTN PIC (P1-PTX-2-100G-WDM), but they can both operate over the same DWDM line system.

Software features

Note: For information about configuring the MIC, see Configuring OTN Interfaces on MIC3-100G-DWDM MIC. For information about upgrading the firmware on the PIC, see Upgrading Firmware on the 100-Gigabit DWDM OTN MIC (MIC3-100G-DWDM) .

• Compliant with ITU G.709 and G.798
• Provides a transport interface and state model (GR-1093)
• Performance monitoring features such as alarms, threshold-crossing alarms, OTU/ODU error seconds and FEC and bit error rate (BER) statistics

• SNMP management of the MIC based on RFC 3591, Managed Objects for the Optical Interface Type, including the following:

  • Set functionality
  • Black Link MIB
  • IFOTN MIB
  • Optics MIB
  • FRU MIB
• Pre-FEC BER monitoring provides interrupt-driven, BER-based detection of link signal degradation for MPLS fast reroute.

• User-configurable optics options:

  • Transmit (TX) laser enable and disable
  • TX output power
  • Wavelength
  • Receive (RX) LOS warning or alarm thresholds
  • Threshold crossing alarms (TCAs)

  User-configurable card options:

  • FEC mode (SD-FEC, HG-FEC, or GFEC)
  • TCAs

Alarms, Errors, and Events

Note: For OTN alarms, see Table 1.

• MIC (FRU) inserted or removed
• MIC (FRU) Administrative State: In Service, Out Of Service
• MIC (FRU) Operational State: Unequipped, Init, Normal, Mismatch, Fault, Upgrade
• Mismatch equipment
• Temperature alarm

• OTU-TCA-BBE—15-minute background block error TCA
• OTU-TCA-ES—15-minute far-end errored seconds TCA
• OTU-TCA-SES—15-minute severely errored seconds TCA
• OTU-TCA-UAS—15-minute unavailable seconds TCA

• ODU-TCA-BBE—15-minute background block error TCA
• ODU-TCA-ES—15-minute far-end errored seconds TCA
• ODU-TCA-SES—15-minute severely errored seconds TCA
• ODU-TCA-UAS—15-minute unavailable seconds TCA

Tip: You can view OTU and ODU TCAs by using the show interfaces transport pm otnoperational-mode CLI command.