Programmable DMX SPI LED Pixel K 8000C SD Card Controller For ucs1903 WS2811 WS2812 LED

Programmable DMX SPI LED Pixel K-8000C SD Card Controller For ucs1903 WS2811 WS2812 LED

Product Parameter

	K-8000C Controller DMX
	Input Voltage	DC5-24V
	Supported chips	LPD8806, WS2801, LPD6803, P9813, SM16716 , DMX512 etc.
	Type	SD card controller
	Working temperature	-20℃~60℃
	Format	FAT or FAT32
	sd card	2GB
	Support Pixels Quantity	Up to 8192 Pixels
	SD card capacity	128MB-32GB
	Output Channe	8 Ports
	Control	Off-oline control
	Application	For led strip,led matrix,led module , led pixel light

Features: 

1. 32 to 65536 degrees Gray control, Gamma correction procession handle.

2. Support different point, line light source, and all kinds of rules and specific shaped handle.

3. The controller has eight ports of output, each port can support up to 512/1024! Üge (DMX lights can support up to 512 pixels).

4. The playback content stored in SD card, the SD card can store up to 32 files, SD maintained capacity supports 128MB-32GB.

5. The controllers can use single set. Also multiple controllers cascade, cascade optical isolation mode: interference, better stability, cascade distance between two controllers can reach up to 150 meters, need to use 0.5M2 pure copper power cord.

6. The controller support chip can lock the support IC in software, or not lock the support IC in the software, select the support IC through the controller CHIP button, this scheme is more flexible and convenient.

7. For the DMX lighting IC, the controller comes with write address function; In addition, using our 2016 LedEdit-K V3.26 or later edition can make a key write address function setting.

8. Support load lamp is 4 channels (RGBW) pixels, or split into single channel point pixels.

9. Enhanced 485 TTLand 485 differential (DMX) signal output.

10. The controller comes with the test effects were as follows: 1 red, green, blue and black jump; 2 red, green, blue and black gradients; 3 red, green, blue and goes

1.If support RGBW four channels’ lights should select K-8000-RGBW.

2.If support single channel light should choose K-8000-W, at this time, one channel means one pixel, the software effect make as white lighting.

Screen print meaning:
Button meaning:

Hints:

1,. The controller load lamps 512 point pixels, speed can be up to 30 frames/sec, 768 point pixel speed can be up to 25 frames/sec, 1024 point pixel speed is about 22 frames/sec (the above parameters is an example of 1903 agreement IC, different IC have difference)

2. International standard DMX512 (1990 agreement) maximum support 512 pixels. When the load is international standard 170 pixel speed can be up to 30 frames l sec, 340 pixel speed is about 20 frames/sec, when 512 pixel speed is about 12 frames/sec.|

3. Timing (holidays) Play Global Wireless GPS synchronization, control station channel distributor, please contact the seller or technical support staff for more information.

Problem 1: After powered on, the controller screen display FFF, and no effect output.

Answer: The screen display FFF means the controller did not read the SD card correctly, the exist problems as
below:
1)SD card is empty, has no effect files.
2)The effect files *.led in SD card and the controller model is mismatch, please select correct controller model,
chip model in the latest edition 2016LedEdit, and remake effect files *.led.
3) Change SD card and then retesting, rule out the possibility of SD card is broken.
Problem 2: After powered on, the indicator is normal, but the lamps has no effects change.
Answer: It has the following reasons for this problems:
1)Please check if the signal line of the lamps and the controller connected correctly.
2)Conventional lamps signal divided into input and output, please confirm whether the controller
connected the first lamp's signal input.
Problem 3: After connect the lamps and the controller, the lamps is strobe and has effect change, at the same
time the controlled indicator shows normal.
Answer:
1)The ground line of the controller and the lamps are not connected.
2)The effects in SD are not correct. The IC of the lamps when making effect is not corresponding with the
IC of the actual lamps.
3)If did not lock the chip, when making effects in the software, need to press the controller chip to the
light's corresponding chip, about press to which number, please refer to the sticker IC order on the controller.
4)The power supply voltage of the lamps is insufficient.
Problem 4: SD card can not be formatted.
Answer:

1)Firstly, make sure if the protection switch on the side of SD card is unlocking. The unlocking direction is
the gold needle side of SD card.
2)The protection has designed as required, but can not formatted, if this condition appears, it always
because the SD card reader is broken, please change the SD card reader(had better use good quality card
reader, SSK card reader is suggested).
3)If the above operations can not solve the formatting problems, please change the SD card and retest.

Support chips (PC Software Choose K-8000-RGB):

00:UCS1903,1909,1912,2903,2904,2909,2912,
TM1803,1804,1809,1812; SM16703,
16709,16712; WS2811; INK1003;
LX3203,1603,1103; GS8205, 8206;SK6812
(Support up to 1024*8 = 8192 pixels)
01:SM16716,16726 (support up to 1024*8=8192 pixels)
02: P9813 (support up to 1024*8 = 8192 pixels)
03: LPD6803 (support up to 1024*8 = 8192 pixels)
04: LX1003,1203 (support up to 1024*8=8192 pixels)
05: WS2801 (support up to 1024*8 = 8192 pixels)
06: LPD1886 (support up to 1024*8 = 8192 pixels)
07: TM1913 (support up to 1024*8 = 8192 pixels)
08: TM1914 (support up to 1024*8 = 8192 pixels)
09: P9883,P9823 (support up to 1024*8=8192 pixels)
10: DMX (Support up to 512*8=4096 pixels, suggestto support <320*8=2560 pixels)
11: DMX 500K (Support up to 512*8=4096 pixels, suggest to support <320*8=2560 pixels)
12: DMX 250K-CZF (Support up to 512*8=4096 pixels, suggest to support <320*8=2560 pixels)
13 : DMX 250K-CZF (Support up to 512*8=4096 pixels, suggest to support <320*8=2560 pixels)

• Items are shipped from China using DHL,FEDEX,UPS and TNT for small parcel. It will takes around 3-7 working days.

• Mass production can be ship via internation express like DHL Fedex or by air or sea.Delivery time depends on destination and other factors, it may takes up to 7 to 30 working days.

Q1. Can I have a sample order for K-8000C Controller DMX ?
A: Yes, we welcome K-8000C Controller DMX sample order to test and check quality. Mixed samples are acceptable.

Q2. What about the K-8000C Controller DMX lead time?
A: About 5-7 working days.

Q3. How do you ship the K-8000C Controller DMX and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping also optional.

Q4. How to proceed an order for K-8000C Controller DMX  ?
A: Firstly let us know your requirements or application
Secondly We quote according to your requirements or our suggestions
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production.

Q5. Is it OK to print my logo on K-8000C Controller DMX product?
A: Yes. Please inform us formally before our production and confirm the design firstly based on our sample.

Q6. What services can we provide?
A:Accepted Delivery Terms:FOB,CIF,EXW,Express Delivery;Accepted Payment Currency:USD,CNY; Accepted Payment Type: T/T,Credit
Card,PayPal,Western Union,Cash